MEDIALINK ROUTER WEBSITE PLUS

The cable is good and I am seeing 120mbps down 11-12mbps up I first tested the 50ft cable plugged directly into my laptop. I tried plugging the 50ft cable from the Xfinity Modem into the LAN port of the Medialink. I can connect to the Medialink Wirelessly and wired but speeds are the same (cut in half). I then went into my Medialink settings and DISABLED DHCP on the Medialink. For some reason after I disable the setting I cannot get back into the router config screen to login to it( I am attempting this wirelessly). The login IP for the Medialink is 192.168.8.1 and I cannot get to the login screen anymore. On my Xfinity router the IP showing for the Medialink is 10.0.0.93 so I set a static IP through the Xfinity Modem for that. Downspeeds improved slightly with my laptop wired to the Medialink to 80mbps down, so there is still a 40mbps loss wired. Xbox One sees about 60mbps down wired which is about a 50-60mbps loss. I do now have an OPEN NAT though so it corrected that issue. I can still connect to the Medialink wirelessly as well but since DHCP is turned off is that going to affect any wireless devices that connect to it?Ĭlick to expand.I have done this. After a factory reset, I can login to the Medialink. I tried following the steps on this link here, read the very last post Its once I disable the DHCP on the Medialink I can no longer access it via 192.168.8.1, this is my problem. Per those instructions the Medialink IP to access the config page would need to be outside of the range of the DHCP addresses of the Xfinity modem. The Xfinity modem access IP is 10.0.0.1 The DHCP range is 10.0.0.2 to 10.0.0.254 I changed the range on the Xfinity to start from 10.0.0.3 to. I then reset the Medialink, I can access the config page after the reset. I went to the LAN SETTINGS tab to set the IP of the Medialink to access the config page. Now you are logged in.The default is 192.168.8.1 I tried to change it to 10.0.0.2 since that is an available address outside of the DHCP range of the Xfinity. Next write the default usernames & passwords of the router to access the admin console.

Visit the web browser of selection & write IP address of the Medialink router in the address box.

Link the router wire to the Laptop or PC.

As, safety of a network is crucial, the first & foremost job is to alter the MediaLink router Default Login & Passkey to something very secure & personal.įollow the commands to login to the Medialink Router.

Whether or not if you have altered the default usernames or passwords of MediaLink & forgot it, just see “How to Reset the MediaLink Router To Default Setting” section.

In both cases, look up the “How to Reset the MediaLink Router to Default Setting” section.

Passkeys find a way to not function! Or, in many events, clients find a method to disremember them.

Make it 15-20 fonts and don’t use the same passkey which you have used for MediaLink router login. Input a recent WPA Pre-Sharing Key / WI-Fi Passkey – this is the passkey which you will use to link to the homebased Wi-Fi. This is the toughest encryption standard obtainable for homebased networks. After you write the network name, you have to allow WPA2-PSK encryption on the router. Search for Network Names (SSID), this is the Wi-Fi name of the Router.

Search for – Basic Wireless Setting (seen in the menu box at the top of homepage), and hit on it.

Search for – Wireless Setting (seen in the menu box at the top of homepage), & hit on it.

Search for – Advanced Setting (discovered in the menu box at the top of homepage), & press on it.

An additional small advice (as it has no effect on safety), is to alter the Default Wifi (SSID) name as it will be more understandable for others to know what network they are linking to.

MEDIALINK ROUTER WEBSITE PLUS

Alter Default Wifi name (SSID) & Passkey plus enables Network Encryption.

However in the end you will end up entering it on a sticky & put it on the router that beats the purpose. Needless to say, you can create a complicated confuse passkey with different characters, numerics, greek plus latin. Provide the Passkey for the router which you will recall (usability first).The volume of safety depends directly on the passkey intricacy, and the efforts taken to safeguard the passkey of your router.It must be something private, for example, means you can never fail to recall it.Select an intricate & tough-to-guess passkey for your MediaLink that just you will recollect.

Medialink router website